Cla-val X144 Technical Manual Uživatelský manuál

X144 e-FlowMeterInstallationMaintenance Operation

Section 2: Installation of the X144 e-FlowMeter (continued) 2.3 - Mounting the X144 e-FlowMeterMount the X144 e-FlowMeter in a proper orientation as s

Section 2: Installation of the X144 e-FlowMeter (continued)2.4 - Step-by-Step Instructions: Mechanical InstallationCAUTION: BEFORE removing pipe plug,

Section 2: Installation of the X144 e-FlowMeter (continued)2.4 - Step-by-Step Instructions Mechanical Installation6) Screw threaded insert into the i

Section 2: Installation of the X144 e-FlowMeter (continued)2.4 - Step-by-Step Instructions Mechanical Installation8) Once the measurement cylinder ro

Section 2: Installation of the X144 e-FlowMeter (continued)2.4 - Step-by-Step Instructions Mechanical Installation10) Ensure that the e-FlowMeter is

Section 2: Installation of the X144 e-FlowMeter (continued)2.5 - Step-by-Step Instructions: Electrical Installation for General ApplicationsFigure 2-1

Section 2: Installation of the X144 e-FlowMeter (continued)13Digital PulseorTransistor (NPN)PulseX144e-Flow Metergreenblueredgreypinkyellowwhitebrown1

Section 2: Installation of the X144 e-FlowMeter (continued)2.6 - Wiring Installation14redyellowpinkbluegrey- 0Vblackred- 0V12/ 24 VDCX144 e-Flow Meter

SECTION 3: X144 e-FlowMeter Operation 3.1 – Starting Operation Follow this procedure when starting the installation for the first time or after shutti

SECTION 3: X144 e-FlowMeter Operation3.2 – Stopping Operation/Removal of X144 e-FlowMeter1) Close the shut-off valves to stop the flow of water, ble

A view inside the X144 e-FlowMeterPlug-and-Play Metering: Cla-Val X144 e-FlowMeterProven Technology fromthe Industry LeaderLaboratory Tested • Field

SECTION 3: X144 e-FlowMeter Operation3.2 – Stopping Operation / Removal of X144 e-FlowMeterd) Slide Insertion Tool straight out, then rotate 180 degre

SECTION 4: Maintenance and Repair 4.1 – Routine Maintenance CAUTION: Always disconnect the power supply, isolate and depressurize the system before pe

SECTION 5: SpecificationsTable 2: Electrical SpecificationsEnclosure Stainless Steel (standard)Output Signal Options:• Digital Pulse, proportionalto f

SECTION 5: Specifications (continued)Dimensional DataFigure 5-1: X144 e-FlowMeter Table 4: X144 e-FlowMeter Dimensions20X144 Sizes1 2 3 4Full Port Va

SECTION 5: Specifications (continued)3.43” 0.04”6.5-inches4.76” 0.04”Insertion Tools: Overall Length •T1 = 6-1/2”• T2 = 14-1/2”Figure 5-2: X144 Inser

Table 6: X144 e-FlowMeter Operational Flow Ranges22Table 7: X144 e-FlowMeter Analog Range (4-20mA Scaling): Factory SettingsIf required, the factory s

X144 e-FlowMeterQuick Start Installation & Removal Instructions X144 e-FlowMeter Included Hardwarepatent pendingCompletee-FlowMeter AssemblyParts

24X144 e-FlowMeterQuick Start Installation & Removal Instructions 7651098Step 5: Insert straightened Swivel Insert/MeasurementCylinder Assembly in

25X144 e-FlowMeterQuick Start Installation & Removal Instructions Digital PulseorTransistor (NPN)PulseX144e-Flow Metergreenblueredgreypinkyellowwh

26X144 e-FlowMeterQuick Start Installation & Removal Instructions Before3Step 3: • Remove the e-FlowMeter Sensor/Head Assembly bypulling straight

X144 e-FlowMeter Installation,Operation and MaintenanceTable of ContentsTopic

www.cla-val.com • 800-942-6326 EASTERN REGION6911 Richmond Highway, Suite 444Alexandria, VA 22306Phone: (800) 451-3030Fax: (703) 721-1927E-mail:

INTRODUCTION: X144 e-FlowMeter Installation, Maintenance and Operation The X144 is an insertion flow meter designed to provide flow information from i

SECTION 1: System Components and How They Work 1.1 - Theory of Operation The X144 e-FlowMeter is an insertion vortex flowmeter based on a phenomenon w

3Figure 1-4: e-FlowMeterX144 e-FlowMeter Parts1) IP68 Submersible Electronics Housing 2) Knurled Lock 3) Centering Pin4) O-Ring 5) Shaft 6) Sensor1265

SECTION 1: System Components and How They Work (continued) 1.3 – Non-Supplied Parts ListThe following parts are necessary for installation and operati

Section 2: Installation of the X144 e-FlowMeter 2.1 - Installation Locations:For optimum performance, it is recommended that the valve in which the X1

Section 2: Installation of the X144 e-FlowMeter (continued)2.2 - Materials Required for Installation Insertion tool • Tool allows the proper installa