Cla-val 350-01/3650-01 Uživatelský manuál

350-01/3650-01

2Flow DirectionThe flow through the 100-01 Hytrol Valve can be in one of twodirections. When flow is “up-and-over the seat,” it is in “normal”flow and

Diaphragm Check (#1 )1. Shut off pressure to the Hytrol Valve by slowly closing upstreamand downstream isolation valves. SEE CAUTION.2. Disconnect or

Maintenance Preventative MaintenanceThe Cla-Val Co. Model 100-01 Hytrol Valve requires no lubrication orpacking and a minimum of maintenance. However,

Lime DepositsOne of the easiest ways to remove lime deposits from the valvestem or other metal parts is to dip them in a 5-percent muriaticacid soluti

15810141661779OUTLETINLETGLOBE PATTERN9262712151416INLETOUTLETANGLE PATTERN22 2313 12 14 10 11 15 23TOP VIEW8" - 24" SEAT DETAIL1 1/4"

100-01Hytrol Valve Service Data MODELINSTALLATION / OPERATION / MAINTENANCEDescription 100-01 Hytrol ValveThe CIa-VaI Model 100-01 Hytrol Valve is a m

COVER PIPE PLUG COVER BEARING SPRING STEM NUT DIAPHRAGM WASHER DISC RETAINER BODY *SPACER WASHERS DISC GUIDE SEAT PIPE PLUG STEM SEAT O-RING STUD 8&qu

UNDERSTANDING THE 600 SERIES VALVESIn 1987, Cla-Val introduced the Model 100-20 Hytrol as the basicmain valve for the 600 Series of automatic control

CLA-VAL Copyright Cla-Val 2011 Printed in USA Specifications subject to change without notice. P.O. Box 1325 • Newport Beach, CA 92659-03

RDH011017,TB_300MultiModeControls.doc,5/5/2005Technical Bulletin300 Series (Multi-Mode) Electronic Actuated Pilot ControlsIntroductionCDB-30, CDHS-30,

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Configuration procedures . . . . . . . . . . . . . . . . . . .2Main power sup

130 Series Actuator Start Up Procedures Introduction It is recommended that this manual is read before applyingpower to the actuator and start up is a

Loss of Signal Conditions.The actuator will respond differently during loss of signalconditions. It will lock in place, rotate fully to the lowest lim

Setting the maximum process variable limit.Method one: Using the system process variable.Set the maximum process variable limit by increasing theactua

LED FunctionMicroprocessor This LED is on when power is applied to the microprocessor, and running the microprocessor is running. If LED is not on, t

Wiring of remote automatic and remote manual operation.There are two modes of remote operation possible with the actuator. They are remote automatic m

7TB41234567219101112TB2Isolated 4-20 mA Tramsmitter -Isolated 4-20 mA Tramsmitter +123456710898TB312345671098TB1Remote SetpointLoop Isolator+_Power Su

8Remote Automatic Mode Using external PV and external power supply to power 4-20 mA loopPower SupplyProcess VariableLoop Isolator(recommended)420 mA P

Remote Automatic Mode Using internal potentiometer asProcess Variable91. Remote setpoint must be isolated and powered from ecternal source.2. PV retra

10Remote Manual Operation - Wiring DiagramPosition actuator using contact closureGround to greenscrew in floorof housingGNL12TB2120/240 AC Input240AC

When ordering parts,please specify:• All nameplate data • Item Number • Description Strainer and Needle Valve AssemblyX42N-23383458218MAX.14253910214M

CLA-VAL Copyright Cla-Val 2011 Printed in USA Specifications subject to change without notice. P.O. Box 1325 • Newport Beach, CA 92659-03

CLA-VAL Copyright Cla-Val 2011 Printed in USA Specifications subject to change without notice. P.O. Box 1325 • Newport Beach, CA 92659-03

3/8" Flow ControlCV2.12MAXSTAMP PART NO. ONSMOOTH SURFACERESTRICTEDFLOW3/8 - 18 NPT1.84ADJUSTING STEM(TURN CLOCKWISE TOINCREASE RESTRICTION)17210

Cla-Val ProductIdentificationProper IdentificationFor ordering repair kits, replacement parts, or forinquiries concerning valve operation, it is impor

HOW TO ORDERBecause of the vast number of possible configurations andcombinations available, many valves and controls are notshown in published produc

Complete Replacement Diaphragm Assemblies for 100-01 and 100-20 Hytrol Main ValvesFor:Hytrol Main Valves with Ductile Iron, Bronze Trim Materials—125/

Repair Kits for 100-04/100-23 Hy-Check Main ValvesFor:Hy-Check Main Valves—125/150 Pressure Class OnlyIncludes: Diaphragm, Disc and O-Rings and full s

Typical ApplicationsSchematic DiagramItem Description1 Hytrol (Main Valve)2 X42N-2 Strainer & Needle Valve3 CRL-30 Electronic Pressure Sustaining

Model 350-01 (Uses Basic Valve Model 100-01)Model 350-01 Dimensions (In Inches)Note: The top two flange holes on valve size 36 are threaded to 1 1/2&q

350-01/3650-01 Purchase SpecificationsThe 350-01/3650-01 Electronic Actuated Pressure Sustaining Control Valve shall have an integral hydraulic and el

CLA-VAL Copyright Cla-Val 2011 Printed in USA Specifications subject to change without notice. P.O. Box 1325 • Newport Beach, CA 92659-0

DescriptionThe CIa-VaI Model 100-01 Hytrol Valve is a main valve forCIa-VaI Automatic Control Valves. It is a hydraulically operated,diaphragm-actuate